Lead4pass 2V0-41.20 Dumps Actual Exam Practice Material Help You To Clear Exam 2023

2V0-41.20 Dumps Actual Exam Practice Material

2V0-41.20 dumps play a key role in preparing to pass the VMware 2V0-41.20 exam, providing real practice material for the exam to ensure a successful pass.

Lead4pass 2V0-41.20 dumps (PDF or VCE) https://www.leads4pass.com/2v0-41-20.html Updated 2V0-41.20 exam practice material with the latest and most accurate answers 91+, worth learning.

Free 2V0-41.20 certification real exam practice and test questions and answers

Free sample questions of 2V0-41.20 free dumps are provided here. 

Question 1:

An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.

Which CLI command disables the nsxcli time-out value on NSX Manager?

A. set cli-timeout 0

B. set cli-timeout enabled

C. set cli-timeout disabled

D. set cli-timeout 1

Correct Answer: A


Question 2:

An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply for the Failover Order as a NIC teaming policy.

Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?

A. N-VDS/VDS Profile

B. Transport Node Profile

C. Host Switch Profile

D. Uplink Profile

Correct Answer: D

Question 3:

Which two choices are prerequisites to configure NSX-T on VDS? (Choose two.)

A. MTU 1500

B. MTU 1400

C. vSphere Distributed Switch 6.5

D. vSphere Distributed Switch 7.0

E. MTU 1600

Correct Answer: DE


Question 4:

Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?

A. ifconfig

B. tcpdump

C. debug

D. ipconfig

Correct Answer: A


Question 5:

Which three steps are required to create an IPsec VPN tunnel? (Choose three.)

A. Create an IPsec service.

B. Add a local endpoint.

C. Configure an IPsec session.

D. Configure a distributed firewall policy.

E. Add a logical switch.

Correct Answer: ABC

Question 6:

An NSX administrator wants to create a Tier-0 Gateway to support equal cost multi-path (ECMP) routing. Which failover detection protocol must be used to meet this requirement?

A. Beacon Probing (BP)

B. Host Standby Router Protocol (HSRP)

C. Bidirectional Forwarding Detection (BFD)

D. Virtual Router Redundancy Protocol (VRRP)

Correct Answer: C

Question 7:

What are two supported N-VDS modes? (Choose two.)

A. DPDK Datapath

B. Overlay Datapath

C. Secure Datapath

D. Enhanced Datapath

E. Standard Datapath

Correct Answer: DE


Question 8:

An NSX administrator has configured a KVM hypervisor as a transport node.

Which kernel module on KVM implements an N-VDS?

A. openvswitch

B. etherswitch

C. nsx-vswitch

D. dyswitch

Correct Answer: A

Question 9:

Which CLI command should be executed on a KVM hypervisor to retrieve the VM interface UUID?

A. virsh dumpxml | grep interface-id

B. virsh get-interface

C. virsh show | grep interface-id

D. virsh list-interface

Correct Answer: A

https://docs.vmware.com/en/VMware-NSX-T-Data- Center/3.0/nsxt_30_admin.pdf

Question 10:

Which two choices are use cases for Distributed Intrusion Detection? (Choose two.)

A. Identify security vulnerabilities in the workloads.

B. Use agentless antivirus with Guest Introspection.

C. Quarantine workloads based on vulnerabilities.

D. Identify the risk and reputation of accessed websites.

E. Gain insight into micro-segmentation traffic flows.

Correct Answer: AC

Question 11:

What needs to be configured on a Tier-0 Gateway to make NSX Edge Services available to a VM on a VLAN-backed logical switch?

A. Service interface

B. Loopback Router Port

C. Downlink interface

D. VLAN Uplink

Correct Answer: A

“The service interface is a special-purpose port to enable services for mainly VLAN-based networks. North-south service insertion is another use case that requires a service interface to connect a partner appliance and redirect north-south traffic for partner services. Service interfaces are supported on both active standby Tier-0 logical routers and Tier-1 routers. Firewalls, NAT, and VPNs are supported on this interface. The service interface is also a downlink”

Question 12:

Which CLI command does an NSX administrator run on the NSX Manager to generate support bundle logs if the NSX UI is inaccessible?

A. get support-bundle file vcpnv.tgz

B. set support-bundle file vcpnv.tgz

C. vm-support

D. esxcli system syslog config logger set –id=nsxmanager

Correct Answer: A


Question 13:

An NSX administrator would like to export syslog events that capture messages related to NSX host preparation events.

Which message ID (msgid) should be used in the syslog export configuration command as a filter?





Correct Answer: B

https://docs.vmware.com/en/VMware-NSX-T-Data- Center/3.0/nsxt_30_admin.pdf

Question 14:

Which CLI command shows syslog on NSX Manager?

A. show log manager follow

B. get log-file auth.log

C. get log-file syslog

D. /var/log/sysloq/syslog.log

Correct Answer: C


Question 15:

The NSX Control Plane is responsible for which two functions? (Choose two.)

A. receive and validate configuration from NSX Policy

B. host API services

C. propagate topology information

D. push stateless configurations to forwarding engines

E. maintain packet-level statistics

Correct Answer: CD


These are just some of the VMware 2V0-41.20 dumps practice material, you can improve yourself with the above questions and answers, and download the full Lead4pass 2V0-41.20 dumps for more.

In conclusion,

Remember that Lead4pass 2V0-41.20 dumps (PDF or VCE) https://www.leads4pass.com/2v0-41-20.html are your ally to pass the VMware 2V0-41.20 exam, make good use of the 2V0-41.20 practice material inside, prepare for the 2V0-41.20 exam, you will be successful.


On our VMware platform, you can search for all free VMware exams and test or practice online for yourself. And can download PDF files. Any other questions, you can email [email protected]